前端预热双温区滑轨炉:带预热炉的可滑动管式炉
前端预热双温区滑轨炉为带预热功能的炉膛可滑动管式炉，有预热炉、加热炉、温控系统、滑动系统组成。
主要特点Main features:
1) Can pull in the required high tem. to sample to get a rapid heating rate; also pull out the high tem. furnace and let the sample in the room tem. Environment to get a rapid cooling rate.
操作时可将实验需要的恒定高温直接推到样品处，使样品能得到一个快速的升温速度，同样也可将高温的管式炉直接推离样品处，使样品直接暴露在室温环境下，得到快速的降温速率。
2) Used for graphene growing or CVD experiment with RTP requirement
应用于有快速升温需要的石墨烯生长或CVD实验。
主要技术参数Technical Parameters
| 电炉名称 | 1100度前端预热双温区滑轨炉:带预热炉的可滑动管式炉 |
|
Power 输入电源 |
Power rated: 3KW 额定功率：3KW |
|
Voltage 电压 |
Voltage rated: AC208-240V 50/60HZ 额定电压： AC208-240V 50/60HZ |
|
Working Temperature 工作温度 |
Max. Temperature: 1200℃( 1 hr) 设计温度：1200℃ (1小时) Continuous working temperature: ≤1100℃ 持续工作温度：≤1100℃ |
|
Max. Heating/colling Rate 升温速率 |
≤20℃/秒 |
|
控温方式 |
PID automatic control and auto-tune function. 模糊PID控制和自整定调节 30 programmable segments for precise thermal processing. 智能化30段可编程控制 Built-in protection for the over-heated and broken thermocouple. 超温和断偶报警功能 |
|
Length of heating zone 温区长度 |
200+200mm |
|
Length of constant zone 恒温区长度 |
100+100mm |
|
Heating Elements 加热元件 |
Resistance wire, Fe-Cr-Al Alloy doped by Mo 高温合金电阻丝（掺钼铁铬铝合金） |
|
Temperature Accuracy 控温精度 |
+/- 1℃ |
|
Processing tube 炉管 |
Φ50/60/80/100*1400mm(optional) Φ50/60/80/100*1400mm(管径可选) Two tube blocks are included for blocking heat radiation generated from tube center.,must be fully inserted into the furnace chamber before heating(quartz or ceramic optional). 两个氧化铝管堵阻挡管中心产生的热辐射，管堵必须在加热前塞进炉膛的正确位置(石英或氧化铝管堵可选) |
|
Vacuum Flange 真空法兰 |
KF25 quick clamp flange 两端为KF25快速卡箍法兰 |
|
Vacuum Pressure 真空压力 |
1pa can be achieved by mechanical pump 机械泵可达1pa 10^-4 pa can be reached by molecular pump 分子泵可达10^-4pa Please click the picture below to order vacuum parts |
|
Warranty 质保 |
One year limited warranty with lifetime support (Such consumable parts as tube, quartz block, and O-rings, etc. are NOT supported by the warranty) 一年质保，长期技术支持（消耗品如炉管，石英管堵，O型圈等不在质保范围内） |
|
Warning 注意事项 |
Small cracks may appear on the surface of the refractory ceramics over extended use. This is a normal occurrence and the cracks may be repaired with alumina coating. 在使用过程中炉膛表面可能出现细小裂纹。这是正常情况，裂纹可以用氧化铝涂层修复。 |
售前客服